Our worm gear reducers offer a choice of a good or hollow result shaft and show an adjustable mounting placement. Both the SW-1 and the SW-5, however, can endure shock loading better than other reduction gearbox designs, making them well suited for demanding applications.
Rugged compression-molded glass-fill up polyester housing
Light-weight and compact
Range of ratios
SW-1, 3.5:1 to 60:1
SW-5, 5:1 to 100:1
Solid or Hollow output shaft
Adjustable mounting position
Worm Gear Swiftness Reducers is rated 5.0 out of 5 by 1.
8 Ratios Available from 5:1 to 60:1
7 Gear Box Sizes from 1.33 to 3.25″
Universally Interchangeable Design for OEM Replacement
Double Bearings Used on Both Shaft Ends
Anti-Rust Primer Applied Inside and Outside Gearbox
Shaft Sleeve Protects All Shafts
S45C Carbon Steel Shafts
Flange Mount Versions for 56C and 145TC Motors
Our regular 700 Series – the heart of EP Gear’s speed reducer products – has been serving industry reliably for over 40 years. Its tested modular design has set the sector standard for efficiency and may be the most imitated product in today’s worm gear quickness reducer market. But why settle for a knock-off when you’re able to have the original – from EP Gear.
11 basic one reduction sizes
8 basic double reduction sizes
1/6 – 25 HP
5:1 – 100:1 ratios single reduction
100:1 – 3600:1 ratios double reduction
Non-flanged, NEMA C-face quill, and coupled input styles
Projecting and hollow result shafts
Projecting diameters from 1/2″ to 2-1/4″
Hollow output bore diameters from 5/8″ to 3-7/16″ (with over 20 bore sizes in share)
The 700 Series’ huge oil reservoir provides efficient heat dissipation and lubrication for longer operating lifestyle.
Its multi-position mounting flexibility permits installation in virtually any position.
Housings are straddle-milled, best and bottom, for precise alignment of horizontal and vertical bases.
Internal baffles assure positive, leak-free venting.
The 700 Series’ rugged housing, fabricated of fine-grained, gear-quality cast iron, provides maximum strength for maximum durability, along with greater precision during worm and gear alignment.
EP Gear’s 700 Series high-strength bronze worm equipment is straddle mounted between heavy-duty tapered roller bearings to increase thrust and overhung load capacities, sizes 713-760.
Our 700 Series’ high-strength steel output shaft assures capacity for high torque and overhung loads.
Pipe plugs allow easy fill up, level, and drain in virtually any mounting position.
The 700 Series’ super-finished oil-seal diameters on both input and output shafts extend seal life.
Both 2D and 3D CAD drawings are available in our eCatalog.
Correct angle gearboxes (worm and planetary) are rugged and built for 90° turns. Inline reducers (parallel shaft and planetary) are an ideal match for motors with high insight speeds, or when gearmotor effectiveness is important. Get in touch with our technical sales personnel for help identifying which gearbox alternative is most beneficial for you.
RIGHT ANGLE REDUCERS
WORM GEAR REDUCER
EP’s worm equipment reducers were created with a hollow bore and invite for a corner change with optional dual result. The reducers can be found in 12 ratios ranging from 5:1 to 100:1, with non-back-drivable ratios 30:1 and higher. Our correct angle gearboxes were created with five mounting choices providing flexibility when incorporating the reducer into item.
RIGHT ANGLE BEVEL GEARBOX
The right angle bevel gearbox combines the features of our right angle worm and planetary inline reducers. With a good and efficient right angle configuration, our right angle planetary gearboxes provide a robust solution. The right angle bevel gearbox comes in 18 ratios which range from 5:1 to 1000:1, in fact it is back-drivable at all ratios.
I-SERIES PLANETARY GEARBOX
Our I-Series little planetary gearbox configurations supply the smallest footprint and quietest operation of our rate reducers. These gearboxes are made to handle varying loads with small backlash. With frame sizes 52cm, 62cm, and 81cm, 12 ratios which range from 5:1 to 308:1, we’ve a solution to fit your needs. Our 52 frame size can be available with plastic-type material gears for noise-delicate applications.
INLINE PLANETARY GEARBOX
Our inline planetary gearbox configurations provide the highest efficiency and best result torque of all our rate reducers. These gearboxes are made to manage varying loads with small backlash. Planetary gear reducers operate more quietly than parallel shaft reducers. With 18 ratio options ranging from 5:1 to 1000:1, we have a solution to suit your needs.
PARALLEL SHAFT GEARBOX
Parallel shaft gearboxes are the best choice for continuous duty applications. Their equipment cluster design provides an effective method for dissipating warmth. Parallel shaft gearboxes possess the shortest amount of our inline equipment reducer options so they work well in environments with limited space. Our parallel shaft gear reducers provide an affordable drop-in substitute solution for most little parallel shaft gearmotors.
Wormwheel gearboxes pass several names, including 90-degree gearboxes, right position gearboxes, speed reducers, worm equipment reducers and worm drive gearboxes. Gear reduction boxes feature a gear arrangement in which a gear in the type of a screw, also known as a worm, meshes with a worm equipment. These gears are typically made from bronze and the worms are steel or stainless steel.
While worm gears act like a spur gear, the worm gearboxes are significantly smaller than other gear reduction boxes. A major benefit of worm gear reducers is usually that they produce an output that’s 90° from the input and can be utilized to transmit higher torque or decrease rotational speed. Most often, a worm gearbox provides right hand threads; to change the path of the output, a left-hands thread worm gearbox is required.
Worldwide HdRS133-10/1-R Cast Iron Right Angle Worm Gear Reducer 10:1 Ratio
Are you looking for worm reduction gearbox? We have actually located !