All EPT shaft collars, including Shaft Clamp quick-clamping collars, are solo point faced to make sure perpendicularity and proper alignment. This critical manufacturing step assures precise shaft collar facial area to bore relationship leading to correct part positioning on the shaft and actually pressure on interfaced ingredients.
Quick-clamping shaft collars from EPT are manufactured from high quality lightweight aluminum with type-II sulfuric anodized finishes, with a dark-colored finish about the collar and a precious metal finish about the clamping lever for added visibility. Lightweight aluminum collars are corrosion resistant, lighter than different metals, possess low inertia and also have non-magnetic properties. All EPT products will be RoHS and REACH compliant. Available typical sizes for the quick-clamping shaft collars will be 0.375” to at least one 1.5” in the in . series and 8 mm to 38 mm in the metric series.
Shaft Collar, Program of Measurement “, Shaft Locking Type – Couplings 1 Piece Quick Clamp, Bore Type – Collars Simple Bore, Bore Dia. 3/8 In., Material – Collars Black Anodized 6061 Aluminum, Outside the house Dia. 1-1/2 In., Width .394 In., Clearance Dia. 1.496 In., Screw Size M3, Screw Material 18-8 300 Series STAINLESS, Operating Temp. Selection -40 Degrees to 200 Degrees F, Requirements RoHS2 Compliant, REACH Compliant
The Shaft Collar 1×3/8, 1/2″ for Key Shaft is made from lightweight Aluminum, both piece design enables you to install these collars anywhere on a shaft without removing components. Furthermore to reducing the entire weight, the flats enable you to rotate a shaft without marring or gouging the shaft. Simply place the collar on the shaft and tighten the two socket-head cap screws to secure the collar and a wrench and be added to the collar’s flats to rotate the complete shaft/collar assembly.
Manufactured from lightweight Aluminum
Lets you install these collars anywhere on a shaft without removing components
Easily place the collar in the shaft and tighten the two socket-head cap screws to secure the collar
Flats allow you to rotate a shaft without marring
Climax Part C-056-S Arranged Screw Collar is made with T303 STAINLESS, which works well in corrosive environments. Measurements will be 9/16 in. Bore, 1 in. OD, 7/16 in. Width. It is effective on hard and gentle shafts. It is a Cost effective collar design, and Very easily installed where significant disassembly would otherwise be required.
EPT quick clamping shaft collars collar clamp hinge buy manufacturing 2 1 8 in metal,shaft collar clamp pressure manufacturing metal vex clamping style,vex clamping shaft collar collars 1 part with lever clamp hinge,vex clamping shaft collar clamp 3d model manufacturing quick 1 3 8 in alum,EPT speedy clamping shaft collars collar clamp 2pc 1 in steel stainless split with lever,climax metallic s shaft collar two piece clamp style EPT quick clamping collars 2pc 1 in steel push,clamp upon shaft collars couplings universal clamping collar design and style with mounting holes 2pc 1 in steel,shaft collar clamp drive clamping calculation quick hook up collars at best value in,clamp shaft collar clamping collars drive calculation quick connect,stainless steel dual split shaft collar with speedy clamping clamp hinge power calculation.
Black Oxide Plated Metal 
One-Piece Clamping Collar.
Recessed Screw Head provides an outside surface free of key projections for safety.
Design completely engages the shaft without marring.
Greater axial holding electrical power than placed screw collars.
Effective on hard & very soft shafts.
Indefinitely adjustable and simple to remove, one-piece clamping collars are usually used on hard or gentle standard round shafts, more than a split hub or upon thin wall tube. Through the use of friction to provide superior grip on bars and shafts, solitary split collars deliver sturdier, more dependable results when compared to the set screw design of solid collars. In addition they offer tremendous axial electricity, while minimizing shaft distortion for top-notch performance and decreased wear and tear.
The collar clamping mechanism works quickly and efficiently with simple hands opening of the integral clamping lever, positioning the collar on the shaft, and closing the lever flush with the external surface of the collar. The design of the cam on the lever and the mating machined surface area on the collar assure a good fit with a optimum axial load of 35 to 120 lbs / 133 to 489 N based on the collar bore size. In conditions where higher holding electrical power is or clamp axial load is necessary, the quick-clamping collar is not the recommended choice. EPT offers a accomplish line of industry-leading one-part and two-part shaft collars suitable for these applications.
